Stanton Professional Performance Mixer SK ONE User Manual download pdf

SK ONE

Professional performance mixer

STANTON MAGNETICS, LLC

2821 Evans St. Hollywood, FL 33020

(954) 929-8999 - Fax: (954) 929-0333

[email protected]

OWNER’S M A N U A L

FA DER CLEA N I N G

The SK ONE faders may need lubrication from time to time. This will extend the

fader life and eliminate any potential damage due to extended heavy usage.

R E PLAC E M E N T PA RTS

To replace the cross or channel faders, follow steps 1 and 2 of the cleaning

instructions. The following replacement parts are available from Stanton or your

local Stanton dealer.

ROTATING AND REPLACING THE INPUT TOGGLE SWITCHES

Cleaning Instructions

1. Remove the 3 fader knobs and 4 screws

located in the corners of the PROTEKT™

(see “ ” inside) panel

and take the panel off the mixer.

2 . Remove the fader to be cleaned by

unscrewing the 2 outer screws (removing

the 2 inner screws will detach the fader

from the fader plate) and disconnect the

cable coming from the mixer.

3. Spray a small amount of cleaner or

lubricant into both ends of the fader and

slide the fader back and forth a few times

to spread the fluid evenly throughout the

fader.

4. Shake and wipe off excess fluid before

re-assembling the fader.

PL-SK1 Two way input toggle switch

3PL-SK1 Three way input toggle

switch with FLASH™

LF-SK1 Channel input fader

CF-SK1 Crossfader

PP-SK1 PROTEKT™ panel

PS-13US US Power Supply (110v)

PS-13EU European Power Supply (220v)

PS-13UK UK only Power Supply (240v)

ROTATING I NST RU C TI O N S

1 . Remove the PROTEKT™ panel

2. Remove the 2 outer screws from the tog-

gle switch plate (removing the 2 inner

screws will detach the switch from the

plate)

3. Rotate the plate to the desired position

and tighten the screws back in the top and

bottom holes

R E PLAC I N G I NST RU C TI O N S

1. Remove the PROTEKT™ panel

2. Remove the 2 outer screws from the tog-

gle switch plate (removing the 2 inner

screws will detach the switch from the

plate)

3. Remove the switch assembly and dis-

connect the cable coming from the mixer.

4. Set the replacement switch assembly in

the desired position and place the screws

back in the top and bottom holes.

1 2 3 4

Summary of Contents

Page 1 - R E PLAC E M E N T PA RTS

SK ONEProfessional performance mixerSTANTON MAGNETICS, LLC2821 Evans St. Hollywood, FL 33020(954) 929-8999 - Fax: (954) 929-0333info@stantonmagnetics.

Page 2 - T RO U B LE S H O OTI N G

PLEASE READ CAREFULLY BEFORE USE OF THIS PRODUCTFA I LU R E TO FO LLOW T H E I NST RU C TI O N S P R I N TE D B E L OW M AY VO I D WA R R A N TY• Foll

Page 3

1. Gain control: Controls the input sensitivity of each channel.2. EQ: Individual controls for low and high frequency equalization with (+9/-26 dB)

Page 4 - FU N C TI O N S (c o n t ’d)

15. Headphone output: Connection for 1/4 inch headphone. Recommended headphoneimpedance is 32-200 ohms for maximum volume.16. Master output: TRS ba

Comments to this Manuals

No comments

Stanton Professional Performance Mixer SK ONE User Manual

Browse online or download User Manual for DJ controllers Stanton Professional Performance Mixer SK ONE. Stanton Professional Performance Mixer SK ONE User's Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for DJ controllers Stanton Professional Performance Mixer SK ONE